Search results

  1. endo617

    endo617: 98 Ej6 Project: Balanced Form

    JDM H22 throttle body here, doesnt have FITV and idle adjustment screw


  2. endo617

    endo617: 98 Ej6 Project: Balanced Form

    Yeah usually I'm like "It drives, screw it" but it started stalling randomly when i made full stops. Idles like a champ now, and cold start is a lot better.
  3. endo617

    endo617: 98 Ej6 Project: Balanced Form

    So here's my symptoms right now""Car Starts up with no problem, once started idle is fine. I drive for a couple and come to a complete stop, idle comes to almost stalling. I have to wait a few seconds idling like that and the idle kicks back to normal. It happens again randomly here and there...
  4. endo617

    Vistas finest 97' Integra LS -

    Actually you could've paid $140 for a JDM DC2 23mm sway, I have one myself installed
  5. endo617

    endo617: 98 Ej6 Project: Balanced Form

    Thanks man Did the head this Friday Got fancy Found this before it caused major damage. I forgot to do the valve lash before start up, whoops. Sounded horrible, but since it was was on I wanted to see if the fan kicked on with the new Gates low temp thermostat and slim...
  6. endo617

    endo617: 98 Ej6 Project: Balanced Form

    Dual spring, Ti Retainers, Skunk2 Stage 1's, Flat Valves
  7. endo617

    endo617: 98 Ej6 Project: Balanced Form

    got toyo R1R's put on, replacing the head tomorrow
  8. endo617

    endo617: 98 Ej6 Project: Balanced Form

    Not that bad. Did my brakes on all 4 corners. RSX DC5 rear big brake is in. Uses the whole pad Rears Fronts
  9. endo617

    endo617: 98 Ej6 Project: Balanced Form

    A bit of a headache this weekend. EX harness my friend give my was messed up. So I had to do all the harnesses twice, then I chased a short that turned out to be the G101 wasn't grounded properly because the bolt was too rusty. But good news is new dash harness fixed my unreadable CEL problem...
  10. endo617

    endo617: 98 Ej6 Project: Balanced Form

    Thanks man, I used the tool enough to pay it off a couple times. I have a good amount of Honda specialty tools. I'm getting ready for Honda Fest 2016 autox


  11. endo617

    endo617: 98 Ej6 Project: Balanced Form

    Head is done ready for install. OE Valve Seals Supertech Springs and Titanium retainers Skunk2 LMA's extra vtec Tow Truck friend scored me a free OEM front bumper.
  12. endo617

    endo617: 98 Ej6 Project: Balanced Form

    Lapping the Valves on my new head, hopefully I can finish and install it next week.
  13. endo617

    endo617: 98 Ej6 Project: Balanced Form

    Works pretty good, and shift light is sick. New Headlights and Tail lights.
  14. endo617

    endo617: 98 Ej6 Project: Balanced Form

    Thanks man. Can't wait to see what RPM I'm at past the stock EJ6 RPM Tach. Has an adjustable shift light too! Finally upgrading the rotors to high carbon and finishing the BBK in the front and rear.
  15. endo617

    endo617: 98 Ej6 Project: Balanced Form

    Picked up some new Skunk2 camber kit for $100
  16. endo617

    endo617: 98 Ej6 Project: Balanced Form

    Making brake ducts, using these cheap EG ones and making them fit. Need to trim the left corners a bit to make it look better.
  17. endo617

    endo617: 98 Ej6 Project: Balanced Form

    LOL yeah it's 2.25" piping and 4.5" tip
  18. endo617

    endo617: 98 Ej6 Project: Balanced Form

    Here's the after on the LCA's, half ass polish Catback came in for the EF. New radiator is in there too with slim fan and shroud, forgot to take a pic.
  19. endo617

    endo617: 98 Ej6 Project: Balanced Form

    I try, thanks man Some parts came in for the Hatch.
  20. endo617

    endo617: 98 Ej6 Project: Balanced Form

    Thanks man. Freebie LCA, going to rebuild and polish Battery bracket made. Need to cut the extra metal and paint it. New BOV pipe came in too Waiting on the tie down.
Top