Edelbrock vs. Skunk2 vs. Blox

[urbano]

i was thinking about upgrading my crappy gsr intake manifold to an aftermarket one but im not sure whih one offers the best performance. anyone know which one of these is a better buy? or know of any other intake manifold brands that i forgot to mention?

 

[guiltyxxspark]

Skunk 2.

 

[cripemaster]

word is that eldelbrock victor x is good, but doesn't have much bottom end power, but more top end. Skunk2 is apparently better balanced with an equal amount of bottom end and top end gain.

 

[Papa_Dios]

I LOVE my Skunk2 as said above very well balanced for a N/A setup....If you're planning on going turbo though I'd say Victor X

 

[bradster101]

any info on the blox one?

 

[tenshi_R]

according to many sources of unreliable info(forums) blox is an exact copy of older skunk2 IM

skunk 2 recently released a skunk 2 PRO version of their intake.
but again. wheres the specs for any of them.
precise measurements side by side would be nice
bcasuse it might be just a trick from skunk 2 in order to steer people away from cheaper blox IM.

post measurements if you can find them, i think i ve seen them somewhere but im overloaded with info and cant remember at the moment.

 

[RobbinYoBizkits]

skunk 2 is good for anything, all their products are great!

 

[emd513]

i think that the skunk is a little more but probably worth it compared to the edelbrock. i will keep checking to see if anyone else puts on stats for these. i also will look and see about stats else where i want to know as well before i buy

 

[emd513]

i would go with a skunk2 there the only ones i can find stats on theres and they offer the power threw the rpm while the edelbrock only does high rpms and the x is 7500 + for power. be your best bet with the skunk , dont know about the blox

 

[urbano]

i think that the skunk is a little more but probably worth it compared to the edelbrock. i will keep checking to see if anyone else puts on stats for these. i also will look and see about stats else where i want to know as well before i buy

ive actually notied that the edelbrock manifold has been more expensive

 

[urbano]

are there any other brands out there that dont cost over 600 bucks?

 

[ixcocoyxi]

theres no point of getting an aftermarket i/m if you dont have internals

 

[urbano]

theres no point of getting an aftermarket i/m if you dont have internals

it sounds like my gsr manifold is leaking

 

[tenshi_R]

? where is it leaking from? u will see a black spot around the hole if it does

 

[Samurai_Blue]

word is that eldelbrock victor x is good, but doesn't have much bottom end power, but more top end. Skunk2 is apparently better balanced with an equal amount of bottom end and top end gain.

victor x is actually built for cars that rev up to or over 10k

according to many sources of unreliable info(forums) blox is an exact copy of older skunk2 IM


skunk 2 recently released a skunk 2 PRO version of their intake.
but again. wheres the specs for any of them.
precise measurements side by side would be nice
bcasuse it might be just a trick from skunk 2 in order to steer people away from cheaper blox IM.

post measurements if you can find them, i think i ve seen them somewhere but im overloaded with info and cant remember at the moment.

Blox supplies skunk2 with stuff and skunk2 supplies blox with stuff they are owned by the same parent company i think

theres no point of getting an aftermarket i/m if you dont have internals

x2

it sounds like my gsr manifold is leaking

either get a type r style one or another one.