2nd Gen Roll Call!
- Thread starter Britty
- Start date
Charly[horse]
Name = John
I'm not sure if I checked in...
Anyway my names John, I have a 90 Rio Red RS Integra ( her name is charly[horse] )
Pretty stock, Megan racing lower rear tie bar, custom exhaust, thats it for now. I have lots of plans for it though!
Anyway my names John, I have a 90 Rio Red RS Integra ( her name is charly[horse] )
Pretty stock, Megan racing lower rear tie bar, custom exhaust, thats it for now. I have lots of plans for it though!
Zypheris
New Member
New to the forums
Just traded my tuck for my gorgeous baby (atleast to me, dont hate)
1993 Acura Integra LS b18a1
-Megan racing 4-1 headers
-Full cold air intake (not sure brand)
-Back Cat (Just looked it was dark not sure if that's right) full system exaust high flow cat
-Stage 1 racing clutch (Doesnt matter its getting replaced soon)
-Skunk weighted short throw shifted
Love this thing got it this way it runs strong
Will post pics soon just wanted to get into the forum and start mingling
Just traded my tuck for my gorgeous baby (atleast to me, dont hate)
1993 Acura Integra LS b18a1
-Megan racing 4-1 headers
-Full cold air intake (not sure brand)
-Back Cat (Just looked it was dark not sure if that's right) full system exaust high flow cat
-Stage 1 racing clutch (Doesnt matter its getting replaced soon)
-Skunk weighted short throw shifted
Love this thing
got it this way it runs strong Will post pics soon just wanted to get into the forum and start mingling
Last edited:
The_Anima7or
The Rook
Black 1993 RS B18A1, no mods yet.. got a pretty gigantic list though. got a battery optimizer on order and a C/F gauge cluster on the way
94EGCoopey
New Member
Allen
'92 DB2 GSR
B16a2 Motor
B17 Trans
Blox Intake Manifold
4-2-1 Header
Full Apex'i Exhaust
GR2's w/ Tein S-Techs
Megan LCA's
Ingalls Camber Kit
AEM CAI
Fixing to put a sleeved 84mm LS Block w/ High Comp pistons on the B16A2 head.
'92 DB2 GSR
B16a2 Motor
B17 Trans
Blox Intake Manifold
4-2-1 Header
Full Apex'i Exhaust
GR2's w/ Tein S-Techs
Megan LCA's
Ingalls Camber Kit
AEM CAI
Fixing to put a sleeved 84mm LS Block w/ High Comp pistons on the B16A2 head.
Detman101
Da9 newbie
Black 93 LS Hatch
Still stock...well, what's left of it.
it's a stripped ex-racing car with the street parts put back on...minus A/C and ABS.
I got it for a daily commuter since the engine and tranny/clutch were good.
I may wind up pimping it out like you all have done to yours...if I can get the money up.
Dm
Still stock...well, what's left of it.
it's a stripped ex-racing car with the street parts put back on...minus A/C and ABS.
I got it for a daily commuter since the engine and tranny/clutch were good.
I may wind up pimping it out like you all have done to yours...if I can get the money up.
Dm
Last edited:
KiddGotBlazed
Blaze
92 Integra RS
Stock motor swapped from an ls
Cold air intake
After market throttle body
Type r lip kit
Black exterior
Black Rota's (Flight) 16" on cooper tires
Stage 4 ACT clutch 6puck
Lowered to 3inches off the ground with tien adjustable springs/shocks/struts
8)
Stock motor swapped from an ls
Cold air intake
After market throttle body
Type r lip kit
Black exterior
Black Rota's (Flight) 16" on cooper tires
Stage 4 ACT clutch 6puck
Lowered to 3inches off the ground with tien adjustable springs/shocks/struts
8)
Last edited: