Too much shifter wobble. HELP!!!!!!!

[DSBDG]

So when I bought my car my shifter went every where even if it was in gear. So I bought some energy shifter bushings and it kind of worked. Now it doesn't move as much as before but it still wobbles, can someone help me out with this. Thanks

 

[jdmjim]

is the piviot wore out?

 

[DSBDG]

is the piviot wore out?

I will check today. Will post results.

 

[DustinXIX]

mine had a bad wobble in it also. whe i was in gear it was like being in neutral 0_0 turned out to be those bushings on the end of the shifter linkage the part that goes on the tranny.i just put a new shifter linkage in and it went away.good luck.

 

[BrokenTalon27]

You could try this as well. I haven't done it but it supposedly tightens up the shifts.
http://forums.g2ic.com/showthread.php?193394-Shift-linkage-u-joint-rebuild

 

[DSBDG]

mine had a bad wobble in it also. whe i was in gear it was like being in neutral 0_0 turned out to be those bushings on the end of the shifter linkage the part that goes on the tranny.i just put a new shifter linkage in and it went away.good luck.

Thanks for the info. That was it!!! The fucking rolling pin is shot and barely hanging on. Don't know how it stayed on. :angryfire:

 

[DSBDG]

You could try this as well. I haven't done it but it supposedly tightens up the shifts.
http://forums.g2ic.com/showthread.php?193394-Shift-linkage-u-joint-rebuild

Awesome link. Will try it this weekend and I will let you know how it goes. Thanks again

 

[BrokenTalon27]

Awesome link. Will try it this weekend and I will let you know how it goes. Thanks again

Please do. If it works I may do it too.

 

[hidenplanvew]

I have done this twice and it does fix the problem (Atleast for me it worked) but I always put the ES shifter bushings in at the sametime aswell with short throw shifter 1000x's better

 

[endo617]

You could try this as well. I haven't done it but it supposedly tightens up the shifts.
http://forums.g2ic.com/showthread.php?193394-Shift-linkage-u-joint-rebuild

x2 nice link, but also did you check the shifter itself?

 

[DSBDG]

x2 nice link, but also did you check the shifter itself?

I did, shifter was good. I'm taking my engine in for a much needed update. it has 240,000 miles and it is going to get completely new internals from the ground up.

 

[hidenplanvew]

Well just do this while its down and you will be good to go... Use some supertech pistons and eagle rods and throw some boost at it... Its only like 600 ish (depends where you buy at) to do rods and pistons and if you want to boost the car you will already have it built for more then what you need on the street.

 

[DSBDG]

Well just do this while its down and you will be good to go... Use some supertech pistons and eagle rods and throw some boost at it... Its only like 600 ish (depends where you buy at) to do rods and pistons and if you want to boost the car you will already have it built for more then what you need on the street.

Thanks for the info. I was wondering what type to get, Its going to be a long week but it will get done. .:thumbs up

 

[DSBDG]

Ok guys, I was trying to put a picture in but I could not figure it out. I will have to explain it. So I think it is called a cam seal its the black rubber piece next to the exhaust cam but I'm not sure, well its leaking and I need to know what it is where to get one and how to replace it. Please let me know and if you know how to put a picture let me know and I will put it up. Thanks