my tegy. 96 integra

NDdb8

New Member
1996 Acura Integra Gsr sedan


its all stock. i add the wheels from my previous car. Rota Slipstreams


Heres after i lowered it



I"ve only owned the car about a month and its coming along ok. i have some damage to work out on the passenger side with minimal rust on the rear. its not bad few things replaced. i got the car from a kid who didnt know hondas/acuras at all. it was handed down to him from his brother and the thing ran like crap. the plugs were so screwed on it. i replace those plug wires oil change and a few gaskets now the cars running great. third gear grinds when you shift hard so lookin to do a tranny rebuild in the winter as well as a motor rebuild.interior is crap, their all tan leather seats so right now im looking for some jdm black interior. the only problem i have is oil is burning somewhere and vtec kinda lags to kick in at 4500 some times so im guessing new vtec selnoid. well thats mainly the details i have for you all now. i will keep posted on the progress of my integra. all comments are appreciated good or bad.thanks for looking! sorry for the craPPY Cell phone pics...my digital cameras screen is busted so these will have to do for now
 

NDdb8

New Member
yea man ive been looking for a good degreaser. i degreased it once and it still looked the same....lol water got into my plugs so i spent about an hour or 2 tryna get water out haha that was a bitch. anybody know of a good degreasing type of soap or anything?
 

Sammich

Active Member
NDdb8 said:
yea man ive been looking for a good degreaser. i degreased it once and it still looked the same....lol water got into my plugs so i spent about an hour or 2 tryna get water out haha that was a bitch. anybody know of a good degreasing type of soap or anything?
Click to expand...
purple power man...ill try to find write up on detailing the engine...but i dont know how u got so much water in ur plugs...if moisture usually gets anywhere its usually the dizzy cap *scratches head*

hey matt u dont have that engine detail i sent u do u?
 

Sammich

Active Member
nevermind found my post on the maxima forum

here is how i do my engine bay cleaning:

1. ensure u have a mildly warm to cold engine

2. start the car up.

3. spray your fenders to dilute any over spray of chemicals getting on your fender paint as you may forget to spray them afterwards

4. spray the engine bay with your degreaser(purple power, mean green, etc)

5. allow car to run for about 10-15mins allowing the grease to loosing itself up

6. (optional, if engine is heavily greased) respray engine bay to softened grease build up and allow to soak for 5mins tops

7. hose off all degreasing solution from the engine bay and remember to rinse fenders again.

8. (optional) spray an engine detailer or armor all over engine bay to provide your 'shine' and close hood and allow car to run another 10mins to allow it to dry and armor all set in.

9. close hood and allow engine bay to dry while the car is still running for another 10mins.

10. pop hood and admire

FYI do not apply a steady stream of water on electrical parts
 

NDdb8

New Member
i can go lower but my mudflap is already scrapin pretty good. i can slam it for a pic but eh. its all good. i do wana lower the front a lil more. the back is tucked a lil lower than the front. bout a smudge lower in front and it would even out.
 

NDdb8

New Member
lol the last pic i think i was parked on a small mound. its a crappy employee lot where my wife works. its being built so its still dirty and gravel and thiers mounds here and their. thats why the driverside shows a lil more gap than other pictures
 
You must log in or register to reply here.
Top